![icom 756 pro ii reset icom 756 pro ii reset](https://i.ytimg.com/vi/e0rJKp7c2rk/hqdefault.jpg)
- #ICOM 756 PRO II RESET HOW TO#
- #ICOM 756 PRO II RESET INSTALL#
- #ICOM 756 PRO II RESET SERIAL#
- #ICOM 756 PRO II RESET MANUAL#
When the system comes back up Verify any changes you have made are still there.It is the last selection and will bring up another menu usually in the middle of the screen. Go to the Raspberry icon at the top left of the screen and after pressing on it select " Shutdown".To do this, on the main mumble screen now showing press Server>Quit Mumble. THIS Step IS IMPORTANT To save your Mumble changes you must Quit Mumble and Reboot.Now on the left hand side of the menu move down to the next menu by selecting "Audio Output" and as you did in step 3 verify the device is set to Default.Just make sure and press apply each time you test another setting from the drop down menu. If you are on V1.05 (not release as of this should already be done for you since the audio card is the default for the RigPi). You can try them all one at a time without hurting anything to see which one sounds the best. If you are unable to determine the correct setting please contact of of the experienced user for help. There are many selections but you want the one that end in default audio. If you receive audio has a watery sound you will need to change this setting to the default sound card setting. If not use the drop down menu to set it to default.
![icom 756 pro ii reset icom 756 pro ii reset](https://i.ytimg.com/vi/X0seop5-Uvs/maxresdefault.jpg)
Verify the Device to the right is set to default.
![icom 756 pro ii reset icom 756 pro ii reset](https://i.ebayimg.com/thumbs/images/g/rzgAAMXQMXRQ4CjE/s-l225.jpg)
If not click on the lips at the top right of the screen. Your mumble menu should showing on the desk top.It should be obvious whic selection is the sound card. The other is the sound card and the name will vary depending on which release you are on. On the RigPi desktop RIGHT click on Speaker icon in the top right hand corner of the screen.
#ICOM 756 PRO II RESET SERIAL#
CI-V baud rate = 19200 This is the fastest speed for the 756proIII CI-V Transceive = OFF USB Serial Function = CI-V This concludes the instructions to the physical radio.
#ICOM 756 PRO II RESET MANUAL#
Here are the settings that need to be changed in the radio: OTHERS MENU (These settings start on in the manual available on the Icom America site available here: ). If you are not please read you manual before attempting these changes.
#ICOM 756 PRO II RESET HOW TO#
You will need to be familiar on how to change these setting in your radio. The Icom 756proIII requires very few settings to be changed so I will list them here. The transceiver displays its initial VFO frequencies when resetting is complete.A/D convertor calibration of the DSP unit starts and it takes 10 sec.While pushing and, push to turn power ON. Here is how is instructions directly from the Icom manual: Resetting CLEARS all programmed contents in memory channels and returns programmed values in set mode to default values. If it doesn't work you can come back and reset at a later time and start over. You will lose all your memories in this process so you are welcome to try all the setting without resetting the radio first. 1.It is always best to reset you radio to the factory setting just in case you have made some setting that may interfere with the operation of the RigPi. The Mic jack on the front of the radio is controlled by the volume control giving more flexibility. Be aware that the audio out is fixed and while there are adjustments in the RigPi for the audio it still may not get you what you need. Here is the link to what you need to order: You can probably get the audio from one of the 8 pin ACC1 jack in the rear of the radio but I have not tested this so you are on your own. It is suppose to come with the cable but some old stock in the stores are missing the cable. I recommend buying the cable directly from MFJ and make sure they include the Jumper cable that you will need. You will need to unplug the mic and plug in this cable when using the RigPi. I have chosen to use the cable that goes from the RJ45 on the audio card to the Mic connector on the front of the radio. You will also need an audio cable to connect the transmit and receive audio from the radio to the RigPi. The one I tested was from Amazon and here is the link: You will need to buy a CI-V to USB cable. The CAT control will be controlled from the 1/8 inch plug CI-V port in the back of the radio. This radio does not have a USB plug for CAT control or audio. Please compare the menu settings to the ones I have provided here for the ProIII. Icom 756pro and IC-756proIII radio setup (the set up for the Icom 756pro and 756proIII are the same) Introduction - Whiles these instructions were developed from the Icom 756proIII manual they should work for all Icom 756xxx radios.
#ICOM 756 PRO II RESET INSTALL#
NOTE: If you install the new audio file per Howard's instructions you will need to use the new overlay as the default system selection in mumble since you are using the audio card.